The indoor fire table below has:
Bronze, Black, Evergreen, Evergreen Reflective, Black Reflective and Gold
The fireplace below has: Bronze and Bronze Reflective, Black and Black Reflective and Amber
The pictures below are of a self install with:
1/4" Bronze and 1/2" Bronze, 1/4" Starfire and 1/2" Starfire
Red Topper
Red Topping and about 1 lb of Scarlet Red Topper.
CLICK HERE TO PURCHASE IN THE E-STORE!
The fireplace below has Bronze and Bronze Reflective installed.
The pictures below are of:
The fireplace below has Bronze and Bronze Reflective with ceramic tile on the outside, very modern and very nice!
The fireplace below has Bronze and Bronze Reflective on top
The fire pit below is in Malibu California which no one could figure out how to do what we did. The customer didn't want to see the fire pit hood anymore. So we just raised it. And everyone said it couldn't be done! This is what we like to do, take imagination and make it a reality. The base was provided by the customer we just supplied the "raise the hood" and the ring and Bronze and Bronze Reflective glass.
The vent went up 20 feet. E mail us and we will tell you how this was done.
The fireplace below is in Rancho Mirage just east of Palm Springs California. This is a direct vent fireplace and we used a Bronze base glass with Bronze Reflective on top. We use the original burner as it would do just fine. We are also cladding the bras with brushed stainless steel and we will post the pictures as soon as we get them. We did two identical fireplaces in this home. One in the master and the other in the family room. You can tell by the back ground.
CLICK HERE TO PURCHASE IN THE E-STORE!
The pictures below will show you how to install a propane burner and valve in your fire pit without drilling a hole in the side of your fire pit with our FPPK (fire pit propane kit). This was install in Calabasas California with Bronze and Bronze Reflective on top. The fire pit has 10" solid sides which made this a good candidate for the FPPK to be installed on the inside wall. This is a propane fire pit and we do calibrate every valve to every ring we install to eliminate back flow and any problems or issues that may happen. We also install the proper air mixer to insure a clean burn as we eliminate the soot know to be produced by propane. If you have a propane fire pit you know what I am talking about.
CLICK HERE TO PURCHASE IN THE E-STORE!
The fireplace below is a before and after and a "how to" make it low and lean. A more contemporary look. This is a self install by Rich Kamins and one very nice job!. He used a Bronze and Bronze Reflective base glass. Topped with a bit of Starfire. Ice Ice Ice and about 2 pounds of Copper Ruby Red Topper for a splash of color.
Typical nasty fireplace before Moderustic!
A few bricks and some drywall
Some sand under the burner for filler to raise the base glass.
And here you have one nice finished fireplace.
The fireplace below is a self install with a 2" base of
crushed lava18 18 double burner
CLICK HERE TO PURCHASE IN THE E-STORE!
The fire pit below was designed and built by Jeffrey Stoutenborough in Santa Barbara, California.
The fireplace below has a base of Gray and Bronze Topped with Bronze Reflective and Gray Reflective.
CLICK HERE TO PURCHASE IN THE E-STORE!
The fireplace below has a base of Bronze with Bronze Reflective and Starfire on top.
This is the back side of the peninsula fireplace.
CLICK HERE TO PURCHASE IN THE E-STORE!
The fireplace below is from Cory here locally in
Rancho Cucamonga California. This transformation was a complete surface make over along with out Sterling Silver interior. The glass that was used was Bronze base glass. This is truly a DIY project and we like to help you create your ideas to reality.
Here we begin with the old interior brick panels removed.
Below you can see the new stone being applied.
Now you can see the reflection on the walls in the
Sterling Silver panels. No, these are not just mirrors in the fireplace. If you do try this, let us know how it worked out for you. Be sure to send us pictures of your project and we will be sure to post it on our "
How Not To Do It Page"! No, Really!
Again we are proud to constantly give you new and exciting products for your fireplace and fire pit projects.
Below is a collection we took pictures for our customer to decide on which base to use under the Amber Diamonds.
Amber Diamonds alone
Amber Diamonds on Black
Amber Diamonds on Starfire
Amber Diamonds on New Yellow
Amber Diamonds on Bronze
The same product can be displayed thousands of ways. What do you want to see? Our diamonds are made with a convex base so when you look at the Diamonds in the fire they seem to be melting on the inside, like looking into a spoon. We cause it to reflect backwards. Visit out "Diamonds Page" to see many more colors!
The fire pit below is going to be installed in Sacramento on 11 14 09 for the Yard Crashers/ DIY/ HGTV show. After it is and has been installed we will post pictures on the Yard Crashers page. In the mean time here is the how to and why. We can build any size, shape, design feature you desire. We build to your imagination.
Below is the catch basin to hold the water for the feature
Above you see the auto fill?
Below the water pump is now install below.
Below the top pan is in place for testing with the fire and water bowls in place
Below the stainless steel ring is installed.
Below the glass (Bronze base glass) has been installed and the lights turned on.
.
Below you can see the pump has been turned on.
and now the fire.
We placed a card board template to replicate the table top to conceal the lights as well.
Now we add color to the water!
Here is the feature exposed with the blue water. You can change the water to any color you like.
This feature is only 6 1/2" tall. You can mount this under the table top and keep it only an inch or so above the surface of the table top.
So let's change it to red water and add Starfire base glass.
Remember, we build to your imagination!
The finished pictures will be posted on the Yard Crashers page when this project is installed after 11 14 09!
The fireplace below was installed by Scott Hansford of Palm Springs California.
We made an aluminum border to separate the glass from the outer stone layer. This helped in design and saved on glass as well. We will explain as we move on:
Do you see how high the gas connection is? We sent a 90 degree elbow to point the gas line down and then added enough filler to the bottom of the gas line to conceal it under the glass.
The metal border is installed holding the outer layer of rock in place.
They didn't like the post in the fireplace so we cut a mirror to preview if in fact they wanted it covered at all. If they would of wanted it covered we would of made piece of super 8 stainless steel (highly polished) to cover the post. The mirror was only a temporary visual. DON'T USE REGULAR GLASS NEAR ANY FIRE! So if you are not sure, preview it. The glass we used was a
Bronze base glass with
Gold base glass and
Clear Diamonds.
CLICK HERE TO PURCHASE IN THE E-STORE!
The fire pit below was purchased locally and then we converted it to burn propane without soot! The colors used were:
Starfire,
Here is what is looked like when he started. These manufactures have no imagination!
This only cost about $100.00, complete!
Mike Clemen installed this next fireplace. He started of with
Starfire base glass and exchanged it for a Bronze base glass.
Then he topped it off with 1 lb of each of the following:
And when he finished it, it looked amazing! Take a look.
Mike has received many compliments which we constantly shares. We do understand why and we were glad to help.
The wine barrel below was build by one of our newer dealers in Texas. Matt's Custom Welding. Contact us for information about Matt's wonderful work. We are going to be much more of Matt's work and look around his showroom in the pictures below. Many more projects to come.
There was a steel bowl installed using our propane system to burn our glass. They used Bronze base glass in the fire pit.
The outdoor fireplace pictures below are in Sacramento, California (for Nancy and Derek Long). This was built by Jake Moss and Jim Corbett who are constantly features on DIY's Yard Crashers! We have worked with them several times and now we continue to help create some pretty cool features together. Here we go:
The glass that was installed is:
CLICK HERE TO PURCHASE IN THE E-STORE!
The next fireplace was installed by Kirk Lewis. He wanted a splash of matching colors and he got it!
He installed:
Bronze base glass,
Bronze Rust Copper,
1/4" Black base glass,
California Gold,
Platinum,
1/2" Bronze base glass,
and 1/2" Starfire.
The next fire table was built by Brian Johnson of Omaha Nebraska, very nice! We supplied the components and Brian did the hard part, the table.
We don't have the construction pictures but we do have the table finished. Add Bronze Base glass and to pit with 1 lb of Ice, you are done.
The blue is actually food coloring.
Additional Links for Bronze.
1/4" Bronze Base Glass Pictures
1/8" Bronze Base Glass Pictures
3/16" Bronze Base Glass Pictures
1/4" Bronze Reflective Base Glass Pictures
Bronze Reflective Base Glass Pictures
1/2" Bronze Base Glass Pictures
3/8" Bronze Base Glass Pictures
1/2" Bronze Base Glass Pictures
1/8" Bronze Reflective Base Glass Pictures
1/4" Chunky Bronze Base Glass Pictures
1/8" Bronze Base Glass Pictures
1/4" Bronze Base Glass Pictures
3/8" Bronze Base Glass Pictures
Bronze Rust Copper Base Glass Pictures
1/2" Bronze Base Glass Pictures
3/16" Bronze Base Glass Pictures
3/16" Bronze Reflective Base Glass Pictures 
