The pictures below are of Dr Micheal Marshall Fireplace Surrounds
CLICK on the link or the picture below to see the surrounds with the Star-Burst Pattern!
The next 5 pictures are from Ursula in Pasadena. She just recently had us update her fireplace with a Sterling Silver interior. Nice touch!
This is a new home with logs and a screen, average at best. Has anyone ever come over to your house and said" Nice Logs"? No and we are going to show you how to create a masterpiece! If you didn't notice, this is a direct vent fireplce
, which means it is an electronic ignition. Flip a switch!
The pictures below are of a typical direct vent
This is a picture of the automatic starter and thermo-coupler.
After you have closed off the bottom of the fireplace and attached the adapter, you're ready for glass!
Here we are testing the burn pattern of the double burners. Our burners have 2 rows of holes in each pipe to give you 4 rows of flames.
After pouring the glass make sure the automatic starter is just above the glass so it can work properly. You can hide it with glass all around the element and it helps if it is in a hole.
We have several more pictures of this fireplace with Ice and a few colors of Toppers
and we will have these pictures up in a few days.
We will also be posting several direct vent fireplaces
to show you how easy it really is.
The 6 pictures below show a self install with all glass using the original burner which didn't have a bad flame pattern. 1/8" Clear
was used as a base and then Starfire
was added to the surface saving money and it did look great. It's a simple as that.
The 6 pictures are of Green, Green Reflective, a 2" install with lava rock filler and is a self install.
The pictures below are of a self install with: 1/4" Bronze base glass and 1/2" Bronze base glass, 1/4" Starfire and 1/2" Starfire Red Topper Red Topping and about 1 lb of Scarlet Red Topper.
The fireplace below is a propane burner, self installation with the 2" method,
Starfire and Gold fire gold on top.
Above we have the old burner with a smaller flame pattern which
we will change to a double burner in our tray propane pan burner
A little bit of cleaning with a wire brush and 1200 degree paint
We filled the bottom with pea gravel and the covered it with sand
Then we installed the propane burner and filler it with pea gravel to the top of the burners
You can see the pilot light and thermo-coupler exposed.
So there it is. A clean burning propane burner, 2" method, no soot, no smells, no carbon monoxide and it puts out a tremendous amount of heat. We sell the 2" method because it works and if anyone tries to tell you different, they need your money more than you do. We are the only company building propane burners for glass that don't soot or smell!
Above the burner goes in below the lava goes on the burner. Then magically the lava disappears! We use the 2" method to save money not gouge the customer as we here this everyday how customers are taken by BS!
This is where is went a little bit wrong, oops. We just had them move the burner
forward and now its fine and the back wall was repainted.
The fireplace below has: A Clear base
with Pale Lime Green Topper
, Red Toppings
, Yellow Amber Toppers
, Copper Ruby Red Topper
, and a hint of Starfire
to lighten the color up.
This is how easy it is to install. This is all glass and if you need to build it up a little or a lot then use a filler to save money.
The fireplace below is s typical simple install. Paint
, Add the glass fire and you're done. This is all Starfire
over an 18 18 burner and 1 can of paint, black. This is how simple it really is!
The fireplace below is in Hope Ranch, Santa Barbara, California. First we installed the double "H" burner.
The we add one match and poof, BLUE FLAMES!
A total of 32 8" Fire Balls
in natural color were added
The customer had a Green
theme and so we topped it off with our Green
As the evening went on the ambient heat drew the flames higher trough the Fire Balls
and the blue was just pure magic. The End!
The fireplace below is in Palm Desert California and was a self install with a crushed lava
over the lava, Starfire
on top of the Clear
and topped with Amber Diamonds
and a splash of our Gold
. It looked great until they found the burner was too close to the back which burned the back wall. I don't know if this was repaired as we did send paint and instructions on how to prevent this in the future. The fireplace looked great except for the "skid mark" on the back wall.
Above it still looked good here!
About our fire glass Diamonds
, they are made of crystal and when you see them in the fireplace you actually see the fire reflection reflecting the flame backward as if the Diamonds
were melting from the inside.
The fireplace below is in Santa Monica California. The fireplace is a Malm Fireplace which can be found at: www.MalmFireplaces.com
Ask for Keith
We used an 18" double stainless steel burner and a bed of Starfire
topped with a few pounds of our Ice Ice Ice.
This is a very simple self installation as you will see.
The house is and was under construction so please excuse the debris around the fireplace. The pictures explain what we did. We didn't change the amount of fuel (BTU's) being burned just the way it looks. Flip the switch, the igniter lights, allowing the gas to come up through the burner and the pilot light lights the gas rising from the burner below. As for the doomsayers that tell you this can't be done, Oh Well! This will be our little secret. If you have any questions on your conversion please send us pictures and we will help you convert your direct vent fireplace as well.
Most fireplace manufactures will tell you this will void your warranty. But you need to actually read the warranty to understand what they will or won't cover. The person telling you this at the factory, ask them what the warranty actually implies. We have read many of these warranties and they won't cover the fireplace anyway. These warranties were written by attorneys to keep the liability from the manufacture and lay the blame on the consumer at any expense, no really read one.
Here is another installation with Blue Green Reflective
This has an 18" x 18" burner with a lava rock and sand base.
This method is will save you 1/3 the cost over a typical installation.
Can you see the crushed lava rock and sand?
This is a simple solution:
Key valve in a metal protective box. I know, too simple.